Reviews Arduino Antenna - BestBuyersPro.com

Arduino Portenta H7 [ABX00042]

Two processors that can run tasks in parallel with both cores communicating with one another. Each core can execute Arduino, mbedOS, micropython, and TensorFlow Lite code..
Comes in the Arduino MKR form factor but includes two extra 80-pin high density connectors. Extend your Portenta H7 to physical interfaces like Ethernet connectors, CAN bus peripherals, extra GPIO pins, SD card, etc..
Onboard WiFi and Bluetooth connectivity up to 65 Mbps transfer rate (using an external antenna)..
Perfect for high-end industrial machinery, laboratory equipment, computer vision, PLCs, robotics controllers, or even dedicated stationary computers..
Main features: industrial temperature rates, 8MB SDRAM, 16MB NOR Flash, DisplayPort output, USBC connector, cryptochip for secure data transactions..

1.Get 51 Arduino STM32 microcontroller routine..
2.With a USB interface, you can watch the computer positioning effect directly phone line..
3.With the passive ceramic antenna and passive antenna amplifier, make better use of the individual effects..
4.With SMA interface can be directly connected to an active antenna SMA..
5.TTL level, compatible with 3.3V/5V systems.(Size:39*25.5mm).

Great influence on the antenna module reception, preferably connected to the 1/4 wavelength of the antenna, typically 50 ohm single conductor. The....
Wireless Transmitter Modules allow your Arduino to wirelessly comunicate with other arduinos, or with radio frequency (RF) controlled devices that....
Antenna position has also affected the reception of the module, the installation, the antenna as possible straight away from the shield, high....
Frequency used to receive, decode and oscillation resistor should match with the transmitter..
Application:Usually used for remote control systems, such as Remote control rolling gates, smart car, smart home, etc..

Operates on LTE CAT-M1 and/or NB-IoT technology + GPS + temperature sensor.
Directly compatible with Arduino Uno, Mega, and Leonardo + easy connection for other logic voltages.
Ultra low-power mode drawing < 8uA, ideal for battery-powered IoT devices + LiPo battery charging.
Kit includes dual flexible LTE/GPS antenna and stacking female header kit.
Detailed documentation, wiki, Arduino library, and code examples on Github + community forum to ask questions.

Get 51 Arduino STM32 microcontroller routine..
with a USB interface, you can watch the computer positioning effect directly phone line..
with the passive ceramic antenna and passive antenna amplifier, make better use of the individual effects..
with SMA interface can be directly connected to an active antenna SMA..
TTL level, compatible with 3.3V/5V systems..

1.ESP-WROOM-32 ESP32 ESP-32S Development Board 2.4GHz Dual-Mode WiFi + Bluetooth Dual Cores Microcontroller Processor Integrated with Antenna RF AMP Filter AP STA for Arduino IDE.
2.Ultra-Low power consumption, works perfectly with the for Arduino IDE.
3.SupportThree Modes: AP, STA, and AP+STA.
5.ESP32 is a safe, reliable, and scalable to a variety of applications.

GPS modules NEO-6M,3V-5V power supply Universa.
GPS Module with Flight Control EEPROM MWC APM2.5 Large Antenna for Arduino.
Module size 25mm*35mm,Antenna size 25*25mm.
Compatible with various flight control modules that provide GPS computer test software.

... same watch, which is more powerful and capable than the former version DSTIKE deauther watches.
There are empty solder pads at the back of this watch which can be soldered to connect ESP8266 with atmega32u4. For example if you solder IIC pads this watch could become a wifi duck.
[Added Atmega32u4 - Bad USB] Flashed Arduino Leonardo bootloader already, the D&B watch can be programmed as bad usb directly. Two buttons(Digital pin 9 and 10) could be used to execute different commands. Moreover, a demo program has been flashed as well. Therefore when bad usb port connects PC, press DP9 button cmd window will be opened. Press DP10 button Notepad will be opened. Which can be programmed via Arduino IDE.
[Improved Battery Capacity - 800 to 1000mAh] Compared to Deauther watch V3, this deauther and bad usb watch V4 has been upgraded the battery capacity from 800mAh to 1000mAh, which will have a longer battery life and the fun will last longer.
Note: there are two usb ports on the watch, and each one could be used to charge battery, but do not suggest to use them at the same time.

A LoRa-enabled wireless board that marries a SAMD21 and a long-range RFM95W to make a compact and easy-to-use IoT board. Compatible with Arduino..
A short (3 inch) wire antenna is sufficient for "short" distances (up to 1 mile line-of-sight), but we've also included a u.FL antenna connector for potentially longer distances..
SAMD21G18A, Cortex M0+, 256KB Flash Memory, 32MHz External Oscillator, 4 Digital and 5 Analog IO Pins with exclusive GND pins.
Hope RFM95W LoRa modem, Point to Point Radio capabilities, LoRa Enabled, Frequency range: 915 MHz, Spread factor: 6-12, Range up to 1 mile line of sight, U.FL Antenna.
LiPo Battery Charger, 500mA Charge Rate. Qwiic Enabled. Power LED disconnect jumper for low power applications. PTH pins for software debug (SWD).

Easy to use, nice range (using antenna on both), you can send strings (text) from one point to another. If you want to automate your house without....
Wireless Transmitter Modules allow your Arduino to wirelessly comunicate with other arduinos, or with radio frequency (RF) controlled devices that....
They work in pairs, meaning you need both a receiver and a transmitter to comunicate with each other.
Compatible with SparkFun’s 434MHz RF transmitter and RF receiver.
This Radio Transmitter & Receiver pair is perfectly matched to allow you to control items from a distance up to 500 feet wirelessly!.