Reviews Amplifier Module Potentiometers

ElecGear 4X Replacement Joystick (EL2 FU 10K) for PS4 / PS3 Wireless Controller, Analog Stick Controller Sensor Assembly Thumbstick Module for Playstation

  • [EL2 FU 10K for PS4/PS3 Controller] – 4x replacement analog joystick was found in some PS4 DualShock 4 came with PlayStation 4 Pro, and some PS3 controllers also use this version. The thumbstick module was made by Favor Union (FU). The stick controller comes with 10KΩ trimmer potentiometers in orange.
  • [Compatibility] – The 14 prongs were positioned as the same as ALPS edition. Technically, the whole unit is interchangeable with EL1 ALPS 10K used in PS4 controllers, and other brands like ‘Scuf’ and ‘Razer Raiju Ultimate’ with ALPS joysticks inside. However, the trim pot resistor alone is not interchangeable with ALPS edition.
  • [Additional Resistor] – Complicated moving mechanism and daily wear and tear finally caused drifting. Even new sensors cannot be 100% balanced. Calibrating in controller settings might not work. We packed 10x correction resistors to solve the potential problem in hardware level. Solder one or two paralleled tiny resistors onto the potentiometer at the opposite direction against drifting. It will help correct 3 to 5 degrees drifting.
  • [When to replace] – The analog joystick needs to be replaced when your controller has the problem of drifting, creeping, stuttering, a blind spot, a dead spot, a dead zone, no react....
Check Stock

HiLetgo 12V~40V 10A PWM DC Motor Speed Control Switch Controller Voltage Regulator Dimmer for Arduino

  • Using imported high-power FET, the load current up to 10A.
  • With fuse, to prevent short-circuit high current, causing burnout protection.
  • With reverse power protection, to prevent damage to the module when the power is reversed.
  • Original 63V / 1000uF large capacitor, to ensure the stability of the module.
  • Potentiometers are equipped with nuts, you can use without adding other components.
Check Stock

JBL VMA1120 Commercial/Restaurant 70v Bluetooth Mixer/Amplifier+6 Wall Speakers

  • ... Front-Panel Display and Controls. Configurable Output Routing. Includes Rack Mount Kit. Specifications: Output Power Per Channel: 120 Watts into 4 Ohms or 8 Ohms. Insertion Loss: 70 V and 100 V Outputs: 1 dB Max. Input Channels: 5. Output Channels: 1. Tone Control: Bass and Treble non-detented potentiometers on each channel Bass: 14 dB @ 50 Hz Treble: 14 dB @ 10 kHz. Bass: 14 dB @ 50 Hz. Treble: 14 dB @ 10 kHz.
  • Input Sensitivity: Mic Input: 5.5 mVrms Line Input: 1.3 Vrms RCA Input (Stereo In): 130 mVrms. Mic Input: 5.5 mVrms. Line Input: 1.3 Vrms. RCA Input (Stereo In): 130 mVrms. Frequency Response: Measured at 2.83 Vrms into rated load impedance at any output 4/8 Ohms Output: 20 Hz to 20 kHz, 2 dB 70 V/100 V Outputs: 80 Hz to 15 kHz 3 dB. 4/8 Ohms Output: 20 Hz to 20 kHz, 2 dB. 70 V/100 V Outputs: 80 Hz to 15 kHz 3 dB. Total Harmonic Distortion (THD): Power Amp Output:.
  • Signal to Noise Ratio: >76 dB. Input Impedance: Mic: 400 Ohms Line: 20k Ohms RCA: 50k Ohms. Mic: 400 Ohms. Line: 20k Ohms. RCA: 50k Ohms. Phantom Power: 27 VDC. Crosstalk: -70 dB. Nominal Input Voltages: Nominal AC Line Voltages: 100, 120, 220, 220 to 240 VAC, 50/60 Hz. Min....
Check Stock

DC 4.5-30V 10Amp Blinking Flasher Module

  • This is a simple and practical blinking flasher module, the ON and the OFF duration can be adjusted separately. The blinking flasher module is suited for both resistive and slightly inductive loads. This blinking flasher module is ideally suited for driving for example LED lamps, hazard lights, warning signs, safety beacons, DC light bulbs, etc .....
  • Operating voltage DC 4.5 to 30V. Maximum current: 10 Amp. Maximum load 300 Watts/at DC 30V, 120 Watts/at DC 12V. (NOTE: this product no step-up, step-down or inverter function, only for DC load).
  • Time-ON 0.01 to 15 seconds and Time-OFF 0.01 to 15 seconds adjustable. The output ON - OFF - ON – OFF… cycle alternates..
  • Two precise 25-turn adjustable potentiometers, you can use a screwdriver to easily adjust the ON and OFF time you need. With LED indication for output status..
  • Compact plastic case and wires connects for easy mount. Two screw mounting holes are convenient for you to fix it on the wall or wooden board. Of course, you can also choose not to lock the screw..
Check Stock

Amp handle, brown raised vintage

  • 100 ohm potentiometer with 1/4 Inch threaded brass bushing for mounting to amplifier chassis.
  • Adjustable level control (using flat head screwdriver). Includes mounting nut and washer.
  • Used as hum balance control in 65 Twin Reverb Machete, and Vibrasonic amplifiers manufactured from 1992-Present.
  • Top-quality potentiometers used on Fender amplifiers.
Check Stock

Logarithmic Amplifier Module ±0.4 DB RSSI Linearity with Limiting Output Can Be Used As FSK PSK Demodulation

  • AD8309 AMPLIFIER MODULE - AD8309 amplifier module, with limiting output, can be used as FSK PSK demodulation..
  • APPLICATION - Used for received signal strength indicator (RSSI) and phase detection in cellular base stations, radar and other radio transceiver applications..
  • 16mA current, 20 mV/dB slope, ‑95 dBm intercede, SMA female, 5MHZ‑500MHZ frequency range, 100 dB gain..
  • ±0.4 DB RSSI LINEARITY - ±0.4 dB RSSI linearity, RSSI scale does not change with temperature and feed voltage..
  • Logarithmic output of the logarithmic amplifier module is proportional to the logarithm of the input signal..
Check Stock

Logarithmic Amplifier Module ±0.4 DB RSSI Linearity ‑95 DBM Intercede, Sma Female Can Be Used As FSK PSK Demodulation

  • 16mA current, 20 mV/dB slope, ‑95 dBm intercede, SMA female, 5MHZ‑500MHZ frequency range, 100 dB gain..
  • APPLICATION - Used for received signal strength indicator (RSSI) and phase detection in cellular base stations, radar and other radio transceiver applications..
  • Logarithmic output of the logarithmic amplifier module is proportional to the logarithm of the input signal..
  • ±0.4 DB RSSI LINEARITY - ±0.4 dB RSSI linearity, RSSI scale does not change with temperature and feed voltage..
  • AD8309 AMPLIFIER MODULE - AD8309 amplifier module, with limiting output, can be used as FSK PSK demodulation..
Check Stock

HiLetgo MEGA2560 ATmega2560-16AU Sensor Shield Sensor Expansion Board V2.0 with Bluetooth SD Card APC220 Wireless RF Ultrasonic Sensor Communication Interface

  • This MEGA Sensor Shield V2.0 dedicated sensor expansion board assembly market a variety of advantages in one of the expansion board design, PCB Immersion Gold processing technology..
  • Board not only all digital and analog interface to the steering gear line order form extended out, but also ad hoc Bluetooth module communication interface, SD card module communication interface, APC220 wireless RF module communication interface, and RB URF v1.1 ultrasonic sensor interface, independent expansion a more easy and convenient..
  • For beginners, do not have to worry about cumbersome and complex circuit connection, will simplify this circuit sensor expansion board in the true sense, it can often be easily connected with the sensor..
  • A sensor requires only a general 3P sensor cable (regardless of digital cable and analog cable), complete the circuit connection, the preparation of the corresponding program downloaded to MEGA controller reads the sensor data, or receive wireless module back pass data through the arithmetic processing, the final easy to complete your own interactive works..
  • Sensor Shield allows you to connect to various modules like sensors, servos, relays, buttons, potentiometers..
Check Stock

Taidacent INA114 Instrumentation Amplifier 1000 Times Gain Adjustable Single-Supply Operation Single-Ended/Differential Input

  • INA114 is a low-cost, high-precision instrumentation amplifier that only requires an external resistor to set the gain, and the gain range is 1 to 10000..
  • the weak signal detection effect is excellent, and can input single-ended signals or differential signals..
  • Chip features: Offset voltage 50uV, drift 0.25μV/℃, and high common mode suppression, 115dB when G=1000.
  • Module application: bridge amplifier, thermocouple amplifier, RTD sensor amplifier, medical equipment, data acquisition front end.
Check Stock

ORION HCCA30001DSPLX Serie Class D SPLX Mono Amplifier 3000W WATTS RMS Stereo Car Amp 2022

  • HCCA3000.1DSPLX Class D Monoblock Amplifier 3000 Watts RMS.
  • Frequency Response 15 Hz to 250Hz +/- 2.5 dB.
  • NEW HIGH PRECISION 51 PIN ALL POTENTIOMETERS W.
  • RMS WATTS @ 1 OHM MONO @ 0.5% THD+N - 3000W.
Check Stock