Reviews Acs34power Supply

Gikfun 20A Range Current Sensor ACS712 Module for Arduino (Pack of 2pcs) EK1181x2

  • pin 5V power supply, on-board power indicator.
  • Package content: 2 x 20A range Current Sensor.
Check Stock

Current Sensing Switch 1~200A DC 10~30V Flameproof Adjustable Current Sensing Switch Adjustable DC Current Sensor Switch(Normally Open)

  • Current sensor chips: ACS712ELC-5A / ACS712ELC-20A / ACS712ELC-30A [There are three specifications for the product 5A / 20A /30A. You can choose the specifications according to your needs.].
  • Pin 5V power supply, on-board power indicator.
  • The module can measure range 5 / 20 /30 amps, corresponding to the analog output 100mV / A.
  • No test current , the output voltage is VCC / 2.
  • PCB board size: 31 (mm) x13 (mm)[One package contains two products with the same parameters.].
Check Stock

ACS712 30A Amp Current Sensor Voltage Sensor Module DC 0-25V Voltage Tester Terminal Sensor for Arduino, Pack of 2

  • Use ACS712ELC-30A chip, pin 5V power supply, on-board power indicator, the module can measure plus or minus 30A current, corresponding to analog output 66mV/A..
  • When no detection current passes, the output voltage is VCC/2..
  • ACS712 is based on the principle of Hall detection, please try to avoid the influence of the magnetic field when using it..
Check Stock

HiLetgo 2pcs ACS712 30A Current Sensor Module 30A Range ACS712 Module

  • Pin 5V power supply, on-board power indicator.
  • The module can measure the positive and negative 20 amps, corresponding to the analog output 100mV / A.
  • There is no the detection current through, the output voltage is VCC / 2.
Check Stock

WayinTop 2pcs ACS712 Hall Effect Current Sensor Module 30A Range ACS712 Module + 2pcs Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor for Arduino

  • 【Perfect Combination】Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
  • 【Current Sensor Module】Chip: ACS712ELC-30A.
  • Pin 5V power supply, on-board power indicator.
  • The module can measure positive and negative current of 30 amperes, corresponding to analog output of 66mV/A..
  • 【Voltage Sensor Module】Voltage input range: DC0-25V.
  • DC input connector: Terminal cathode connected to VCC, GND negative pole.
  • Output interface: "+" then 5/3.3V, "-" then GND, "s" then the for Arduino AD pins..
  • 【Package Included】2 x ACS712 Hall Effect Current Sensor Module + 2 x Voltage Sensor Module DC0-25V Voltage Tester Terminal Sensor.
Check Stock

Current Transmitter AC 0-200A Conversion Analog 4-20mA AC Isolator Transformer Converter Current Transducer

  • High quality current sensor chips: ACS712..
  • Pin 5V power supply, on-board power indicator..
  • The module can measure positive and negative current of 30 amperes, corresponding to analog output of 66mV/A..
  • A fixed bolt hole for easy installation..
  • Using this product can measure both voltage and current, very suitable for DIY electronic design projects..
Check Stock

FainWan ACS712 Current Sensor Module Detector ACS712ELC 5A 20A 30A Amps Amperage Range (Pack of 2) (5A)

  • Pin 5V power supply, on-board power indicator.
  • The module can measure the positive and negative 20 amps, corresponding to the analog output 100mV / A.
  • There is no the detection current through, the output voltage is VCC / 2.
Check Stock

Slim DIN Rail Mount AC/DC Current Sensor Module, Based on ACS712. (+/-20Amp)

  • The item disign based on ACS712 IC. The item provides economical and precise solutions for AC or DC current sensing in industrial, commercial, and communications systems. Typical applications include motor control, load detection and management, switched-mode power supplies, and overcurrent fault protection..
  • Operating Voltage: Regulated 5VDC. Operating Current: 20mA(max). Load Maximum Current: +/-5Amp, +/-20Amp and +/-30Amp selectable. Load Frequency Bandwidth: DC ~ 80 kHz. Minimum Isolation Voltage: 2.1 kV(RMS). Output voltage proportional to AC or DC currents. LED indicator for power supply +5V. Pin jumper option for signal output capacitor..
Check Stock

MyVolts 12V Power Supply Adaptor Compatible with/Replacement for Linksys WRT1900ACS Router – US Plug

  • This 12V high-quality replacement power adapter is compatible with the Linksys WRT1900ACS Router..
  • The plug fits a US 2-pin wall power socket..
  • This power adaptor is designed to meet the power specification of the WRT1900ACS Router referred to here – it is the correct voltage, amperage and tip size..
  • It meets and exceeds all US safety standard, features overvoltage, overcurrent and short circuit protection to protect your device, and is energy efficient..
Check Stock

Results RNA ACS 200 Colloidal Silver Gel Extra Strength | Advanced Cellular Silver Topical Gel for Sunburn, Wounds, Rashes, Skin Irritations (2 Ounce)

  • SOOTHING AND EFFECTIVE | ACS Silver Gel provides soothing and discernable rejuvenation for all skin types. Use daily for brighter, healthier skin..
  • SUPERIOR SILVER | Powered by the same patented technology as ACS 200 Extra Strength..
  • ZERO SIDE EFFECTS | Other topical creams and ointments can actually damage the skin. ACS Silver Gel Extra Strength provides exceptional effects without harmful chemicals..
  • DIRECTIONS | Apply liberally to the skin. Cover the skin as desired with a thin layer 1 to 3 times daily. Do not rinse off..
  • INGREDIENTS | Ultra-Pure Deionized Water, Carbomer, Advanced Cellular Silver 200 Parts Per Million, L-Glutathione Tripeptides (Reduced), Acetyl-L Carnitine, Lipoic Acid (R-Fraction), L-Glutamine, TMG (trimethylglycine)..
Check Stock