Reviews 5 flute Reamer

PAGOW 1/2\ Hand Reamer, High Speed Steel H7 6 Straight Groove Reamer, Straight Flutes Hand Milling Cutter Tool

• Premium Material: The material is low alloy steel with high hardenability and low hardenability. The reamer has the characteristics of high wear resistance, less severe cutting and less deformation..
• Hand Reamer: Reamer for reaming holes have been drilled after processing (or reaming) on the workpiece, mainly to improve the precision of the hole, reducing its surface roughness, is finishing and semi-finishing tool for the hole..
• Straight Flute Tool: 6 Flutes & Straight Shank. Allows chips to collect in the flutes when cutting, well suited for most applications in shallow cuts..
• Application Object: Installed in the lathe for cutting of metal tools. Straight flute hand reamers is used in ferrous metals and most nonferrous metals. Designed for accurate reaming in aluminum, cast iron, copper, magnesium alloy, plastic, wood, etc..
• Application: Good for general purpose applications, offering combination of hardness and toughness for wear resistance. Features just the base substrate without any additional treatment or coatings, suitable for wide ranges of applications..

Drill America Bridge (Construction) Reamer 15/16\ Magnetic Hex Shank Bridge Reamer

5/8 Bridge Reamer Bridge/Construction Reamer 1/2 Shank M2 HSS Taper Chucking Reamer Bit Tool for Steel Metal Alloy Wood Plastic Drilling Hole

• Material: 5/8 bridge reamer is made of high-quality M2 HSS steel, with high toughness, high-temperature resistance, corrosion resistance and long service life. Compared to other commonly used low-grade high-speed steels, M2 has an increased content of tungsten and molybdenum, both key elements for improved durability.
• Wide Application: HSS bridge reamers can enlarge or align existing holes and are suitable for various materials such as aluminum, brass, bronze, cast iron, copper, iron, metal, nickel, plastic, steel and other structural materials Note: It requires existing holes Or a pilot hole is required.
• Size Infor: Length of chucking reamer is 6.5 inch.
• Safe to Use: Designed with helical flutes and safety stops to keep chips away from the operator. The safety collar stops to prevent over-penetration and loss of operator stability.
• Design: The tapered tip design allows the reamer to fit into unevenly overlapping holes, aligning the bolt holes. The 5/8" bridge reamer is not a drill, it just aligns the reamer with the pre-drilled hole.

29/32\ Expansion Reamer, Carbide Tipped, Straight Shank, Partial Flute Carbide 56018P, USA Made

• When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
• 1 1/2 " flute length, Partial Flute Length Carbide.
• 3/4 " shank diameter, For Reaming abrasive material.
• This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

15/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56069P, USA Made

• When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
• 1 1/2 " flute length, Partial Flute Length Carbide.
• Morse taper shank #3, For Reaming Abrasive Material.
• This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

29/32\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56068P, USA Made

• When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
• 1 1/2 " flute length, Partial Flute Length Carbide.
• Morse taper shank #2, For Reaming Abrasive Material.
• This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

13/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56065P, USA Made

• When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
• 1 3/8 " flute length, Partial Flute Length Carbide.
• Morse taper shank #2, For Reaming Abrasive Material.
• This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

1 3/16\ Expansion Reamer, Carbide Tipped, Straight Shank, Partial Flute Carbide 56026P, USA Made

• When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
• 1 3/4 " flute length, Partial Flute Length Carbide.
• 1" shank diameter, For Reaming abrasive material.
• This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

1 7/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56080P, USA Made

• When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
• 2" flute length, Partial Flute Length Carbide.
• Morse taper shank #4, For Reaming Abrasive Material.
• This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..

1 5/16\ Expansion Reamer, Carbide Tipped, Tapered Shank, Partial Flute Carbide 56078P, USA Made

• When the diameter wears down to the low limit, it may be expanded oversize, reground to size and recleared. The expansion screw should never be loosened in an attempt to use the reamer for a size smaller than that to which the tool was originally finish ground. These reamers are inteded to be used for 1 specific diameter, not multiple diameters..
• 1 7/8 " flute length, Partial Flute Length Carbide.
• Morse taper shank #4, For Reaming Abrasive Material.
• This is an expansion reamer NOT an adjustable reamer. It can be expanded only and reground..