Reviews 2 probe Connector - BestBuyersPro.com

GAOHOU PH0-14 Value Detect Sensor Module + PH Electrode Probe BNC For Arduino

Getting the voltage varies on what you’re using. The PH for this sensor is not at 0v for a PH7 it’s around 2.51v from the multi-meter and PH4 at 3.03. If you calculate the step, 2.51-3.03 =-0.52. The difference between ph4.01 and PH7 is 2.99..
If you’re using a Particle product like the Photon or Argon, be aware of a bug. It’s a hardware issue with the analog ports fluctuating a ghost voltage. This fluctuation is enough at these low voltages reading to make your ph sway by .7 or more. To fix this, you’ll need to add a 0.1uF cap between the analog port your using and ground..
This PH electrode probe must be calibrated with standard buffer solution before each use, and the electrode probe cannot be tested continuously for a long time, which will shorten its life. There are two trimmers on the circuit board. One of them is for offset adjustment (closest to BNC connector) accomplished by removing the Ph probe and shorting the BNC connector with a wire. The other trimmer is an upper limit threshold for the digital output pin..

Connector Type : Banana Plugs, Testing Pin.
2.High quality with special sharpness and gilding.Around 1 meter length with terminal.
Package Content : 1 Pair x Multimeter Probe.Black and red needle point test probe..
4.Easy access to ICS, LED, SMD, etc.Resistance of the probes: .
5.It is Super sharp, can easily through the cable cortex. But please don‘t force to the hard object..

This is the P.I.N.D.A probe version 2 Compatible with Prusa i3 Mk3 mk3s mk2.5 mk2.5s 3D Printers..
This probe is exactly the correct probe and has been tested with same electronics and firmware as the original probe and works to same effect..
Wire length and molex connector included..

Includes: ORP Probe, Probe Storage Bottle, Platinum Polishing/Cleaning Strip.
Designed especially for the PINPOINT ORP Monitor and the PINPOINT ORP Controller or any meter/monitor/computer interface with a BNC Input.
Probe comes with a 10 foot high suppression cable and a BNC connector.

2mm/0.07" probe tip ,90cm / 35" total length, banana Connector..
Two colors, black and red,anti slip grip increased superior handling, ease of use..
With banana Connector to pin-probes, it is commonly replacement for most all economical test meters requiring the standard male banana Connector..
Easy connect to universal digital multimeter standard jack.It is one of the useful tools that will brings a lot of convenience for your electronic work..
Perfect for testing electrical wiring circuits, anti slip grip increased superior handling, ease of use..

Universal Oscilloscope Probe 10:1 and 1:1 Switchable Bandwidth 100MHz,Usable with Scopes having Bandwidth up to 100 MHz.
Interchangeable Probe Tip.High Sensitivity, Excellent Performance and Reliable Function.
Fully-Shielded Welded BNC Connector, Small Signal Interference.
Pure Copper Plated Gold Pin for Good Contact Test Versatility and Capability..
Used with Oscilloscopes from All Manufacturers , Equipped with The Standard BNC Connector..

> Compatible with all Traeger Wood Pellet Grills (EXCEPT PTG) with digital control meat probe capability, please check spade connector style before....
> Strict quality control standards to Build and test. Not OEM but quality exceeds OEM requirements. Easily spliced to thermostat leads, no tool....
> 37"(18cm) Internal Grill Sensor Probe, 47"(120cm) Heat Woven Wires. Screw and nut are not included, extra thin probe tip leaves a smaller puncture....
To monitor the meat temperature or ambient temperature (smoker/grill), This probe works very well on smokers....
> Guarantee and Service: The probe sensor Replacement Part completed with a One-year Warranty. Save much money off dealer prices. If the probe once....

Universal Oscilloscope Probe 10:1 and 1:1 Switchable Bandwidth 200MHz,Usable with Scopes having Bandwidth up to 200 MHz.
Interchangeable Probe Tip.High Sensitivity, Excellent Performance and Reliable Function.
Fully-Shielded Welded BNC Connector, Small Signal Interference.
Pure Copper Plated Gold Pin for Good Contact Test Versatility and Capability..
Used with Oscilloscopes from All Manufacturers , Equipped with The Standard BNC Connector..

...it is a must-have for modern auto mechanics and is suitable for a wide variety of vehicles from all markets including Europe, America and Japan..
【Multi-Function Circuit Test Lead Kit】LED stroboscopes are used to test voltage and ground signals, such as Hall sensors, fuel injectors, solenoid valves, etc. The SRS connector is used for the electrical simulation of belt tensioner generators. 5KQ potentiometer (variable resistor) is used for components such as engine cooling systems, oil sensors and temperature testers..
【Time-saving and Efficient Test Lead Kit】The circuit test lead kit is designed to provide a wide range of test coverage to accurately and quickly detect vehicle problems. When you need to check parts, you can directly connect to the back of the terminal to avoid damage to the circuit. If you need to check the current, you don't need to cut the wires, just connect the line to the circuit..
【92 Pieces Test Lead Kit with Carrying Case】The multimeter test lead kit comes with a portable black storage case, which makes it easy to sort and organize all your test leads and accessories so they don't get lost. Packing List: Black carrying case、testing leads x72 (36 male and 36 female terminals)、LED stroboscope x2、standard probes x2....